VEMS Home Products Documentation Wiki Webstore
WikiHome ProjectPage DocsPage UnderDevelopment MembersPage SiteIndex RecentChanges Preferences
MembersPage/MarteleurTim (2015-01-01 07:00:00)

I want to turbocharge my BMW 518i E28 M10 engine by using VEMS

For ease of reading i've added page 2 to this document:

[page2]

Installation specific

Trigger/ignition plan: MembersPage/MarteleurTim/Ignition

ITEMS TO BUY:

I recommend buying a pre-assembled Genboard to avoid this part of the project, but in case you feel confident with electronics and like the idea of saving some money - then go ahead. I would advice you to fully populate the board with as many fuel injector FETs and ignition IGBTs as you can afford - they can be used for a lot of other things and the minimum I'd recommend is 6xFET + 5xIGBT. That allows you to run a direct-fire (distributorless) setup in the future.

Q: What about TPS? Should I look for a TPS with WOT switch and potentiometer?

A: A true potentiometer type TPS is recommended for full use and control. A WOT switch is not much use, it can be used to raise boost target with BoostControl. In MegaTune you configure and calibrate the maximum and minimum TPS values (idle and WOT). You can also set the idle threshold value (1-2%).

Only in some cases do you really need to know the exact position of the throttle plate. You can use a resistor grid with the stock "on/off" TPS, to make three distinct positions/resistance values (idle, in between, WOT). It has worked really well on this car: MembersPage/MattiasSandgren/BmwSevenTwentyEight

The basic idea is to connect the TPS In (EC36-1) to a pullup resistor towards +5V (EC36-28) and a pulldown resistor towards GND. The pullup resistor is shorted by the WOT switch (raising TPS In to +5V) and the pulldown grounds the signal. To protect from a short (should never happen), connect a resistor between GND and the pullup resistor and Idle-switch so that there is a minium resistance to be met between +5V and GND at all times. Use 1K resistors, or similar size.

[A drawing of the circuit used with the stock TPS]

Q: How will I control coldstart issues?

Q: should I use the solenoid type or the mechanical type from the Ljet? What is the easiest and most reliable?

[Picture of Auxiliary air valve (usually L & K-jetronic)]

or this one from the motronic

[Idle air solenoid]

A: I'd use the Motronic to get the most control, it's a bit experimental but it would be neat if you could get it working properly. Gergely is working with this one on his BMW. You can find Gergelys work here: MembersPage/GergelyLezsak/IdleControl

If you want to avoid the guesswork you can use the older bi-metal "Auxiliary air valve", it does a good and reliable job and is activated as the "fast idle" valve, and shuts off at a specific temperature.

Q: When I use the Auxiliary air valve how will the electrical heating be ensured?

A: There are two types of auxiliary air valves, most are electrically heated while a few early types are only heated by the engine block/head/coolant. When the valve is cold the blocking plate rotates or pivots to allow bypass air, when it's warm the blocking plate closes the opening. Both types have a bi-metal arm that moves the blocking plate and that is what is influenced by both engine temperature (by being bolted to the head usually) and the electrical heating on newer models. The engine temperature is the major factor on a warm engine, the electrical heating has little merit here and is usually controlled by the thermo switch usually found on the thermostat housing of engines equipped with these. You can use the default EC36-pin3 (P259, 4) to ground a relay that in turn delivers power to an electrically controlled auxiliary air valve.

Q: Do I need the coldstartinjector too?

No, of course not. You use the warmup enrichment bins to add fuel for cold starts.

Assembling V3.3

Q: Can I follow the same instructions as for V3.2 for connecting powersupply and connectors for serial cable etc...?

A: Yes, only the trigger connection is different, the 2x3 pin header now misses the south-east pin. Connect the northern middle pin to the north-east pin to get the primary-trigger forward.

[Picture of Genboard v3.3]

Q: Do I have to connect a connector onto the 3pin header which I soldered on the board for the serial connection? Or is this done through the EC18?

A: You can do it either way. If the box is mounted in a location that makes it hard to reach in there to connect the serial cable, it is a good idea to permanently mount a serial port in the car and wire it through the EC18-connector. I would recommend a custom cable using a 6.3 mm phono plug (for audio use), it can be bought through the webshop.

Power Up

Some issues here:

When serial header is connected and EC36 has power and GND I have communication with the PC using Megatune (succes! => so your firmware operates), but with the TerminalProgram you want to say sg. like "Manmcd" so the controller prints it's config (than "bye" or reboot before letting MegaTune talk to the board again.)

If I type man mdv , the PC recieves alot of strange symbols on the recieving screen but nothing understandable?

Thanks Mattias. This is OK I get a 'Hello' from the board in Terminal!

If it's the newest, there is little urge to reflash

  • however, you can verify
I don't understand this (I am a beginner in this kind of stuff), you should explain things more explicit, like type this in this program and then do this because it's too difficult for me. Thanks for your patience and help anyway!

(not write, just verify mode; prog.pl vems.hex :COM2 Etf or UsabiLity/GenBoard/WinTools or megaloader with whatever option ). If this verify fails, you might want to reflash (the firmware in might be compiled with nonstandard options, such as IGN_DUALOUT. This is not clear from the short "1.0.18" version

text)

21/10/2005 Firmware r027 succesfully uploaded!

OK LCD working and no damage so far as on misconnecting the LCDheader.

PS2 keyboard

The JP_PS1 headers is the one in this picture, to the left of the Atmel. Pin 1 is the one furthest from the EC connectors and also farthest up in the picture. Documentation on this is under reconstruction, I can't find the old page anymore. //Mattias

JP_PS1Mini DIN6Function
14Vcc
23Gnd
31Data
45Clock

[PS2header]

PROBLEMS WITH POWERUP

Q: Problem with power up? When I power up the genboard there is highlighted: 'V.E.M.S. Firmware: 1.0.19' but it stays like this all the time (sometimes only a few letters are visible). I think it should move to a starting page?

A: Can you communicate through the serial port with the Genboard the only thing I can imagine is a LCD misconfiguration. What is your current config? Try disabling busy polling in the LCD settings.

Yes I can communicate through the serial port. If I disable busy polling the problem is fixed.Thanks Mattias

Q: But other problem rises: I have a AZERTY keyboard but it should be QWERTY I guess? Is there a solution?

Q: What should be the configuration for the TPS? I still have 56% when throttle is closed.

A: In MegaTune, go to the menu Tools -> Calibrate TPS and get the values for idle and WOT. Enter those in Settings -> Basic Settings window. You can use a narrower range of values to ensure that there is no movement due to a noisy signal (there should be no noise). Experiment and you'll understand.OK

Q: When in Megatune, the last 6 or 7 redbullets on the bottom of the screen disappear for a millisecond from time to time and meanwhile also the values(needles) drop to zero???? Is this a bad contact somewhere?

A: Check that you have a matching megatune vemsv3.ini with your current firmware version, either that is the problem or a bad serial conn.. You can probably see a RESET counter increasing in the lower left corner of the main screen..

OK changed vemsv3.ini from new firmware to Megatune directory and problem is solved! Thanks Emil!

IGNITION MAP

Q: As I don't see anyone who have an ignitionmap of an standard 1.8i M10 engine, I wonder how difficult it will be for tuning up the engine? Is there any possibility to run the engine in the first stage only with fuelcontrol by the VEMS and in the mean time log the actual standard ignition parameters with the VEMS by using the standard ignition setup?

A: I would start off with 15 degrees timing on idle, 35 degrees around 100 kPa, 25 at 150 kPa and 15 at 250..

SETUP FOR HALL

With a V3.3 board you must solder the necessary jumpers for a specific trigger setup. (with the assembled controller the trigger option must be selected, so it's set up for you).

See GenBoard/Manual/InputTrigger and (recently cleaned up) GenBoard/Manual/InputTriggerHardWare, namely "v3.3 (trig1) primary trigger=HALL" section.

instructions:

v3.3 (trig1) primary trigger=HALL

solder JP2 & JP7: this is the top right of the 2x3 header; red on the [image]. The same area of v3.3 looks slightly different (no bottom-right pad, where the blue jumper sits on the image), but never mind.

short SJ2

do NOT short SJ6 (remove the blob if there)

R30=2k7 pullup resistor (2k .. 4.7k). Note that 10k is a bit too high

remove R56(=18k, next to SJ2). This is not necessary if R30 is 4k7 or lower.

measure DC voltage between SJ2 and GND (with board powered, but HALL sensor not connected or inactive): must be higher than 3V

Any of the 2 (slightly different) v3.2 instructions would work too.

SOLDERED THESE COMPONENTS ON V3.3

1. Flyback lead see pic: [flybacklead]

2. From Rescue kit1 the inductor marked 1R5 must be soldered Between A&B.

If a fused power supply is being used then a wire must connect 1&2, otherwise a fuse link must be used. see http://vems.hu/www.vems.co.uk/VEMS/ConnectingPower.htmlpowerconnections

3. EC18 + EC36 connector

4. 8 IGBT's + 8 FET drivers

5. MAPsensor

6. PS2header + connector

7. LCD Header + connector

8. Serial header + connector

9. D37 Transient supression diode [diode mounted]

10. solder JP2 & JP7

11. solder R30=2k7 pullup resistor

If there was no torture (like running injectors without GND5 or flyback), the P259 should work. Thanks Marcell. I thought that those channels give an groundsignal for a led too. But this isn't the case.

Q: Can I test the coil output with a relay?

Q: How can I assign my 4 injectors to a known channel which I can test with a mdh command? I've read the digitalout section but this is very confusing for me.