_______ 
(       )
| () () |
| || || |
| |(_)| |
| |   | |
| )   ( |
|/     \|
         

         
         
 ##  ##  
 ####### 
 ####### 
 ## # ## 
 ##   ## 
         

         
|\     /|
| )   ( |
| |   | |
( (   ) )
 \ \_/ / 
  \   /  
   \_/   
         

  _  __
 | |/ /
 | ' / 
 |  <  
 | . \ 
 |_|\_\
       
       

         
|\     /|
( \   / )
 \ (_) / 
  ) _ (  
 / ( ) \ 
( /   \ )
|/     \|
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
http://i196.photobucket.com/albums/aa262/shushu4345/ignitionsetting.jpg ---- '''Ignition outputs are wired like''' Firing order: => 1 2 4 3 (not 1 3 4 2) '''Bad wiring''': From bottom to top ^. * cyl 3 ignch2 EC36pin34 output 20 * cyl 4 ignch7 EC36pin10 output 70 * cyl 2 ignch6 EC36pin24 output 60 * cyl 1 ignch3 EC36pin36 output 30 This wiring is not suitable for ign_dualout (so with 4 coils, you would need camsync). '''Recommended wiring''': From bottom to top ^. * cyl 3 ignch7 EC36pin10 output 70 * cyl 4 ignch2 EC36pin34 output '''20''' * cyl 2 ignch6 EC36pin24 output 60 * cyl 1 ignch3 EC36pin36 output '''30''' ign_out=72 h[2]=70 '''30''' 70 '''30''' 00 00 00 00 The reason for this is because with ign_dualout (N, N-1 rule), * selecting ignch7 will also fire ignch6 * selecting ignch3 will also fire ignch2 My fuse keeps blowing everytime I crank. I have setting coilcharge time to 0.58 ms, but still it keeps blowing. Not that ignition preparation status was not enough for wiring (and configuration), yet alone to start cranking ! ''' I have seen this problem, it turned out that the car I worked had a CDI ignition system from the factory and CDI coils are not compatible with an inductinve ignition system. In my case I could get it to give very weak spark at 0.1-0.2ms dwell and 0.0 added at 6v. Measure the primary resistance of the coil and report that, the result of the resistance measurement may not be conclusive but it's a start. - Jörgen''' primairy coil 1.3 ohm secundairy coil 11.49 Kohm 10A shared fuse for 2 coils is not recommended. Prefer 4..5A/coil for initial startup. It should idle OK and revv upto at least 4000 RPM without blowing. Than upgrading to 7.5A / coil for production minimixes the chance for blowing at bad time. '''Do NOT EVEN think about a 20 A fuse !'''. 10A is already too much, it might allow peak 15A so it might not provide proper protection. ---- Scope of my primary http://i196.photobucket.com/albums/aa262/shushu4345/13334.jpg
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.