#       
 #       
 #   #   
 #  #    
 # #     
 ## #    
 #   #   
         

 __   __
 \ \ / /
  \ V / 
   > <  
  / . \ 
 /_/ \_\
        
        

   ____ 
  / ___|
 | |  _ 
 | |_| |
  \____|
        

 __          __
 \ \        / /
  \ \  /\  / / 
   \ \/  \/ /  
    \  /\  /   
     \/  \/    
               
               

         
         
 #####   
 ##  ##  
 ##  ##  
 #####   
 ##      
 ##      

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
We are a couple of guys doing our project work on The car electronics program(Bilelektronik) at Elof Lindälvs Gymnasium in Kungsbacka south of Gothenburg in Sweden. The engine we should perform the VEMS on is a Volvo engine called B5234T or a B5254T we're not sure yet. '''5 cyl engine''' in any case. We've got two identical engines with some parts that is gone but one should be able to be complete. We have not ordered our genboard yet but we should take the discussion with the "economic man" as soon as possible so it wont take too long time. Well i'm going to keep you as updated as i can. It would be nice if someone who has done the instalation on this type of engine before could help us with some knowledge. //Johan ---- '''Trigger section''' Trigger is the most important part to get right: if this is sorted, the rest should not be too hard (although everything requires some research and planning) * 60-2 crankwheel - confirmed by Emil ** VR (just a guess). Emil disassembled a 850R engine once, and that one had 60-2 drilled into the flywheel (VR or HALL sensor ??). Johan will do some research * 1 pulse on cam (HALL) - confirmed by Emil Trigger is very similar to 5cyl audi with aftermarket 60-2 wheel. ---- '''VE''' Even if this engine is not very common, the head is the same as 4cyl volvo-s, so starting VE map can be borrowed (easy to tune with the wideband in any case). RE:sounds really good for me =) ---- '''Ignition table''' of a similar 4cyl can also be used, as long as the compression ratio (CR) is close too. Good starting point should not be a problem anyway. ---- '''Wiring''' '''Econoseal is worth its price''', planning to use that. *Do you need some "special" wire to conect into the Econoseal? ** 0.5 or 0.75mm2 silicone insulation wires are most common (cheapie car manufacturers use PVC, but that is being phased out). We want to get more (striped) colors, see http://wiki.x-dsl.hu/cgi-bin/w/elparts.cgi?Cable/Silicone ---- '''From Tyresö Gym''' Hello we just ordered our genboard and planning the wiring at the moment... we have a bit of problem cause the ecm harness is going thru a imobilzer module. Otherwise it have went well. When you order your genboard be sure to order it with the rigt options. Mvh Carl, Johan, Dennis, Christian, David FP3 Tyresö Gymnasium. Re: can you get it with different options? What do you have to know then to get the correct options? I'm going to check the engine and get the correct model and name tomorrow. Mvh Johan and Marcus
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.