#    #  
 #    #  
 #   ##  
  ### #  
      #  
  ####   

 _______ 
(  ___  )
| (   ) |
| |   | |
| |   | |
| | /\| |
| (_\ \ |
(____\/_)
         

 _______ 
(  ____ )
| (    )|
| (____)|
|  _____)
| (      
| )      
|/       
         

 _       _ 
( )  _  ( )
| | ( ) | |
| | | | | |
| (_/ \_) |
`\___x___/'
           
           

  _____  
 |  __ \ 
 | |__) |
 |  _  / 
 | | \ \ 
 |_|  \_\
         
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
My name is Balázs Nagy. Specifications and mods related to my Nissan. '''Engine''' '''Nissan Skyline GTS-t RB25DET Spec2''' Inline6 * firing order: 153624 * 2.5L with Vct (Variable Cam Timing) which will be quite hard to program. Logic level Ignition coils (unlike on the rb25det spec1engine) Mods Mitsubishi Lancer Evo 7turbo with stock manifold using converter Front mount intercooler Costum IC pipe External wastegate Costum made aluminium radiator with built in heat thermostat for electric fan HKS super sequential bov (atmorpheric) Tomei fpr Full 64mm exhaust '''Ecu Ordered''': 1 x v3harness - injectors: I6 - with_connector: LSU4.9connector - with_relays: yes - extra TESA tape: no 269.06EUR 1 x ECU VEMS V3 - withSDcard: no - Special requests: no - Service: slow - secondary_trigger: HALL - primary_trigger: HALL - mounting-style: unspecified - MAP connection: 300 kPa simplenipple - LCD connection: no - Knock input channels: 2 - ignition driver: 6+2 - Hi-side PFET outputs: 0 - Flyback: HighZ-only 30V flyback - ETC BridgeOutput_Interface: 0 - EGT input: 1 - 1-wire interface: no ---- '''Progress''' - '''Install''' Ordered Vems, forgot to write in "nissan" for engine specifications, so modifying order for Nissan Hall trigger. Guys said it could be solved by ignoring secondary trigger abouve 2500 under secondary trigger settings I ordered the Ecu with 6high current outputs and 2 logic level outputs, so Im planning on using the 4 stepper drivers to control the other 4 ignition modules. They are all logic type moduleles. '''Injectors''' Although functionally not an issue: Some '''nice order like A,B,C,D,E,F would be nicer for firing order 153636''' (unless generic harness + already plugged in => than leave as is) EC36 Pin7 InjectorA - cylinder No.1 on engine EC36 Pin9 injectorE - cylinder No.5on engine EC36 Pin8 InjectorC - cylinder No.3 on engine EC36 Pin18 injectorF - cylinder No.6 on engine EC36 Pin19 to InjectorB - cylinder No.2 on engine EC36 Pin20 InjectorD - cylinder No.4 on engine '''Ignition''' I rewired the Ignition (listing as 123456 is BOGUS ! Always think and list in firing order !) In 153624 firing order: * Ec36 pin 11 logic level output with green wire goes to cylinder No.1 * Ec18 pin 5 stepper output with yellow wire goes to cylinder No.5 * Ec18 pin 4 stepper output with purple wire goes to cylinder No.3 * Ec18 pin 11 stepper output with green/black wire goes to cylinder No.6 * Ec36 pin 12 logic level output with orange wire goes to cylinder No.2 * Ec18 pin 10 stepper output with red wire goes to cylinder No.4 Power to ignition coils goes to fusebox with two red/black wires, I will use each of them to power 3-3 coils with 12V and the stock Nissan coils need 30amp fused power '''LSU4.9''' Vems warned me about checking the harness. Checking every connection, Eg if the Bosch LSU WBO2 connections are okay, and to make sure it's not wired according to the older (and different according to "7-x" rule) Bosch LSU 4.2 pinout. The '''wiring was perfect for LSU4.9''' as the following: Ecu EC18connector pin6 with yellow wire is connected to LSU4.9 pin 2 Ecu EC18connector pin9 with red wire is connected to LSU4.9 pin 1 Ecu EC18connector pin13 with black wire is connected to LSU4.9 pin 6 Ecu EC18connector pin18 with white wire is connected to LSU4.9 pin 3 LSU4.9 pin 4 with grey wire is connected by the harness to fusebox with 5amp fuse '''Fuel Pump Wiring''' Fuel pump is controlled by VEMS from EC36 Pin15 goes to the fuel pump relay. The relay has a blue wire wich connects direcly to the fuel pump's 12V power feed wire. Fuel pump needs grounding on chassis and that is all. '''Knock Sensor Wiring''' - White protected VEMS loom goes to knock sensor directly from Ec18 Pin01. It is a one wire connector, no need for grounding or annyting else. * see EC18 paper (EC18/pin1 is almost always first knock input, when nr of knock inputs > 0) '''Nissan VCT''' (Variable Cam Timing) Nissan VCT is a two wire solenoid. One of them is constant 12V, and the other is ground controlled by VEMS. VEMS switches it on/off with one of the injector outputs by giving grounding it when it needs to be activated. It does not matter which wire goes where on the solenoid,it is interchangable. I choose EC36 Pin06 to control it. '''VEMS Grounds''' Since Im using VEMS harness, I used the two grounds included in the harness. One is grounded near the firewall, one is grounded on the drive shaft tunnel next to the shifter. '''VEMS Ground is Ec36 Pin05,Pin21,Pin22,Pin26,Pin32. Connected on Vems Harness to common ground no need to worry about it.''' '''Ec18 Pin17 is 2nd WBO2 heater''' (when ECU is ordered with dual WBO2) so EC18/17 is '''intentionally NOT connected to other grounds in generic v3 harness''' * EC18/17 not connected to ground, but when ECU has single WBO2, it is allowed to connect to other grounds, or use it to activate inputs (wheelspeed/wheelspeed2, HALL type third trigger, analog input) or analog input reference ** I joined it to common ground '''VEMS 12V Feed''' Since im using a in cabin battery kill switch I can just join the 12V feed (thick red cable) with the ignition on signal cable (thinner orange cable). No need to worry about draining my battery, since the kill swich will turn off all electrical connection in car while not using it. '''CAS sensor''' (Crank Angle Sensor) CAS provides the engine position signal and RPM signal to VEMS. Wiring is the following: Trigger 1: Connected to VEMS EC36 Pin27 Primary trigger Trigger 2: Connected to VEMS EC36 Pin13 Secondary trigger 12V supply: Connected to battery. Ground: Connected to VEMS harness ground. '''TPS''' (Throttle position sensor) EC36 Pin29 TPS Supply is connected to TPS power in TPS Earth is connected to VEMS harness earth Ec36 Pin1 (TPS IN) is connected to TPS singal out. '''Idle control valve''' '''question''' How does VEMS control idle? * Very easy to answer: see [http://vems.hu/vt/help/v3/v3_starting_idle_menu.html VT help] ** [http://www.chiark.greenend.org.uk/~sgtatham/bugs.html also read How to Report Bugs Effectively] (same is also useful for phrasing questions? eg I was looking at ... expected ... but found ... or did not understand ... part)
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.