### ## ### ## ## ## ## ## ### ## ## ## ###
#### ## ## ## ## ## ## ####
_ _ | | | | | | | | | | | | | |_| | \___/
_______ ( ___ ) | ( ) | | | | | | | | | | | | | | (___) | (_______)
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: '''Subpage of AfreshTiny''' '''Using [http://shop.vems.hu/catalog/display-only-round-p-134.html Display-Only Round] or [http://shop.vems.hu/catalog/roundwbo2egt-p-101.html full featured Round] to display data sent by the v3 (or other AIM-dash compatible) ECU''' This means that it's '''unnecessary to purchase and install a 2nd set of sensors''' - a significant '''saving of ~150..300 EUR'''. '''Overview:''' '''Round provides better readibility than an LCD for the most important parameters like''' * '''Lambda''' * '''EGT''' * MAP * RPM * '''wheelspeed''' * or other ---- '''Steps''' Important: please '''follow the steps precisely'''. Consult the [http://www.vems.hu/manual/vemstune/help2/htmls/main/round.html vemstune help], also available from the vemstune program. Start there. * For AIM, the setup procedure uses VemsTune (newer than 2010-09-29). * Round (with AIM-capable firmware) is capable to receive AIM (standard aim protocol 19200,8n1 rs232, 5bytes per packet) from PC or v3.x or other aim-compatible ECU (or transmitter device) * '''AIM-capable round FW releases are''' versioned as '''0.x.x version''' (eg. 0.4.8). Find the actual one on AfreshTiny/FirmwareUpgrade . Note: 1.4.8 does NOT have AIM support. (it cannot display data coming from AIM, and related menus/settings might be missing in vemstune). * the genboard can send realtime AIM data (v3 ECU firmware >= 1.1.42) * '''Any channel sent by the sending device can be displayed on top or bottom display, with any scaling, offset and dot position''' * any number of rounds can get the data (eg. 1 genboard feeding 9 rounds displaying total 18 data). VemsTune support is implemented. '''Install Firmware''' Installation of an AIM capable firmware is the same as a Non-Aim Firmware, see AfreshTiny/FirmwareUpgrade '''Default config''' A default config is available at VemsTune/defaultfirmwareconfigs directory or at http://www.vems.hu/files/Display/Round/round-aim-default-config.msq for MegaTune You can use it as a starting config, but never forget to write down to a paper your calibration values (egt_cal, egt_offset, wbo2_pump_pw_zero, wbo2_nernstdc_target ) and set it up after config upload. '''Displayed values''' Display state (mode) can be switched with the button (if button is enabled, see AfreshTiny/AnalogInput): 8 sets of top/bottom values can be configured * the last received AIM data is displayed. If the display does not update, check the serial line and the sending device. You can use a switch in the serial line to intentionally cut the circuit at the desired time if you like (Hold function). '''Connection''' * to PC: just connect Round's RS232 port to PC's com port * to ECU: connect RS232,pin 2(tx) ECU side to RS232,pin 3(rx) ROUND side and the pin 5(ground) on both ECU and ROUND side ** if you use more than one ROUND the rx pins are common ---- Setting '''v3 ECU''' with VemsTune to send AIM stream * v3 firmware must be at version '''1.1.42''' or later * to enable with VemsTune (must be newer than 2008-09-30) (or Megatune): ** Outputs menu / Display Settings / AIM Enable http://www.vems.hu/files/Display/Round/vt_aim_ena.JPG * to enable in config files: set lcd_c0 bit2 * ECU can't connect to PC and Round at the same time ---- Setting '''Round''' with VemsTune to receive and display AIM values: Follow the steps at VemsTune Help: http://www.vems.hu/manual/vemstune/help2/htmls/main/aim.html ---- AIM protocol ** Aim realtime data types and numbers: ***http://www.vems.hu/files/MembersPage/NanassyPeter/AIM_support/AIM-ECU%20protocol.pdf ---- OLD method with Megatune (not recommended) '''Setting Round''' with megatune to display data received via AIM Round firmware must be newer than 2008-08 with '''Megatune''': (You will find in the round firmware's uzipped directory) * AIM enable: ** in Settings menu / Display settings http://www.vems.hu/files/Display/Round/mt_aim_ena.JPG * AIM settings: http://www.vems.hu/files/Display/Round/mt_aim_set.JPG ** There exists configuration (aim channel and Ax+B linear transformation) for 2 top (T0,T1), and 2 bottom values (B2,B3) ** Channel x num: there you can choose the number what to show as Tx ** Channel x mul(%): the data from ECU has different format, with this value you can multiplicate ( 0..2X ) ** Channel x add: the data from ECU has different format, with this value you can add offset *** Zero means 8192 so you can incrase or decrase value with 8192 ** Channel x dot: the data from ECU has different format, with this value you choose where to show the dot * Display settings: ** You can show 8 sets of top/bottom values Measured and Aim data too http://www.vems.hu/files/Display/Round/mt_aim_disp.JPG '''Using:''' * After power up the well configured ECU will send the AIM data and the connected Rounds will show as it configured * The switch on the Round will change the 8 display modes (disp_state variable) ---- '''Feedback''' from round => genboard (eg. button for launch or table-config-switch?) is not currently planned. The genboard firmware internal CLT temperature representation was -40..+102C. Around 1.1.4x it was changed to max +155C. Sending via aim does not change the limits. ---- Because I use right now only 4 slots, is it possible to make disable other fields that I do not use. Yes it's not something wery important... but it wold be a lot easyer not to go over other 4 that I do not use to get back to first one. * After firmware x.5.1 the maximum number of display slot can configure from 1 to 7 in display settings dialog Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.