VemsTune/WishList (2020-03-18 09:39:28)

Wishlist

This page should generally contain only wishes and observations about functionality, not bug reports.


Multiplexer channel setup

Currently A0 and B0 aren´t available normally, can this be fixed in the next release so that all 8 channels are available in the Analog gauge menu

Also the MUX filtering only has 6 total channels as well

Also the MUX calibration section only has 6 total channels as well

These just all need to be the normal and not need any addition by users.


Rolling Launch Control on Motorsport menu an option to enable a rolling launch control that only retards ignition timing with no spark cut. Example of usage is when rolling 60mph and there is a need for boost to be built faster the driver can press a button and hold and when the throttle is above 90% timing retard is applied allowing the turbo to make boost rapidly. Keep the throttle above 90% and release the button for instant power. I have tested this using the nitrous controls and it works extremely well.

Rolling Launch Control Menu Options

Launch Control Menu Addition Add the option for launch control to activate above X TPS position for those who do not have wheel speed input. With activation above X TPS along with clutch switch allows for the feature to not activate in most normal driving situations.

Additions to A/C control small 4x4 or 6x6 tables for timing and fuel around idle or below 100kpa that is an adder to the main tables. after testing 1.2.38 firmware with AC control it does not work well in my car and i have reverted to map switching to adjust my fuel and timing accordingly at idle. beyond idle my car seems to function well with AC on. These tables should be triggered when the AC input wire chosen is turned on.

Hard spark cut RPM limiter only instead of hard spark cut being 200RPM- fuel cut just add drop downs to pick weather spark cut, fuel cut or both enabled. some of us prefer the spark cut only for the drama caused.


Multicast=enabled; Multiple VemsTune -s (possibly on several continents) simultaneously receiving runtime data from the same VEMS ECU

Displaying gauges, logviewer, datalog; note: currently only the master can change ECU config/table values.

Useful eg. for "tuning party", where friends or experts can follow a tuning session and propose changes / experiments.

TODO: write recommendations, examples how to use when master VT is behind NAT, eg. mobile broadband

"Multicast" function has been available since VemsTune 2014-09-09

The slave VemsTune-s can be older than 2014-09-09 (but latest VT recommended anyway)

Unfortunately, most internet connections are crippled:

See VemsTuneMulticast

  • EXPERTS ONLY: http://samy.pl/pwnat/ pwnat allows direct connection from slave VT to master VT (even if both are behind NAT); The slaves can connect if they know the IP address of the master VT (like with a webserver); but the server does NOT have to know the client IP address (this is obvious for a real server but very tricky when server and client are both behind NAT).
  • depending on the NAT box, it cannot always connect (without third party to tell the peer's IP) if both client and server are behind NAT - it's very tricky situation and the ICMP / UDP workaround tricks don't work if the firewall is very restrictive

Auto Tune. Inspiration for developers http://www.youtube.com/watch?v=qwkqjotkDJQ&feature=related



Device specific profiles'

Now we have alot of PnP variants floating around and I think it would be great if when a user connects to the ECU for the first time you can select the ECU variant from a list(V3, Audi variants, Peugot, BMW, Citroen) . Then pinouts shown in dialog menus are based on the OEM Pinout and not VEMS pinout, this would help ALOT with supporting customers with PnP ECUs.

Vemstune could also automatically look up the serial number from the server and based on what it finds shows the right pinout automatically, this feature could be a offline database as well.


General wishes

http://www.britishv8.org/Articles/Ignition-Tuning-201.htm

Found this program Virtual dyno and hope we could have the same function in Vt so we can see when we are making more power Hp/Nm

VirtualDynoDJ.jpg

http://www.bradbarnhill.com/projects/VirtualDyno/

make a 2000-6000 pull and 100% tps

Convert to .csv

open csv file in excel

delete the first line “vems” to make it work

Nice functions to have in Vt:

Peek Nm and Hp

3 runs graph in the same row

Measurement on the fly

Was implemented as a log-analysys expert tool: LogAnalysis/PowerCompare . A more user-friendly, and possibly realtime tool would be nice though.

Addition to this idea -

Re-iterated in hopes of implementation into Vemstune or as an example :

Vemstune can export real .csv files not tab delimited files named .csv like now and they can be opened via Virtual Dyno.

The first line of the log where it says "vems" could be skipped.

The .csv file can be made from viewing a section of log in the Log View and right click - save as .csv file

Then it can be opened by Virtual dyno without any editing.

csvexport.jpg


Wish for the Round

A wizard to create the wideband custom curve would be very useful, just a simple two point linear curve generator would suffice in most cases that allows you to simply set min/max lambda and corresponding min/max output voltage. It's also useful to have a test-mode where you can force the output while checking for the same result in the ECU that receives the signal. The test mode is useful for all output types, not just the custom curve. I got within 0.01 AFR acurracy from 10:1 to 20:1 AFR with an Autronic unit, if not for the test mode I would have been 0.4 AFR off at either end of the signal.

Download WButil for TechEdge WBO2 and play with it: [Unzip and run]

Here is how it's curve wizard appears with the test mode,

The blue line is the wideband units signal and the red line is generated from the wizard. The crosshair is at the test output voltage.

round-output-wizard.png


Log viewer

22/12/2015

Request for data channels to be shown on the right hand side like so

Toolbox_Example.jpg

Selecting channels in log viewer should not need a descriptor before being selected into log viewer, when a channel is selected and no descriptor is available Vemstune forces the user to make one or makes one based on max and min values found in the data.

Allow flags to be channels with their respective values but the right hand side shows the text definition from VemsFlagDescEditor

Save selected area should be called "selection export"

Any chances on implementing additional math functions? like filtering, integration over time, differentiation against time, previous value comparison and registry creating? Even if it´s only possible in Log viewer and not real time, more important that way anyway, especially with heavy math.

like

integral(channel_name) , and say you have roadspeed as the channel you get distance as the product, or if you have acceleration you get velocity and so on,

or

differentiate ( GPSspeed ) , gives you acceleration and so on .

  • Custom expression being able to be used in multigraph would be a good start
  • The custom expression gauge output certainly cannot be plotted in MVG, since the magic happens inside the gauge, it does not create a new 'channel'
  • but any new expression added to the ini (manually), can be plotted in MVG without issues
  • (as long as compiled ini's is disabled, that will favor the expressions in the ini over the hard-coded faster ones). All rules that exist for showing a new ini channel on a 'normal' gauge also apply to MVG here, before being able to use the new channel first you need to create a descriptor for it via View->Editors->Add new symbol descriptor.

Any of the below ever coming (X/Y plots, 3d histograms, multiple log files, log file comparing, having to resort to megalogviewer is far from ideal)

Separate topic on support forums : [link]


Documentation

There are a number of variables where it is not clear what they control by the descriptor in the main dialog box.

Every proposal should refer to some actual dialog (and preferrably have some proposed text, or note about what part is difficult to understand, or point to better description or inconsistency ).


More red text


Postponed ideas


Display boost pressure in other units of measure

You can simply take the current KPA value and feed it through another equation to give other units of measure.