Hi everybody,
New here on this forum.
My name is Michele and i'm from Belgium.
My project car: VW GOLF MK4 1.8T 20V AGU engine 1999.
The mods:
-Turbo TD04L from subaru WRX
-Homemade stainlessteel egal lenght exhaust manifold
-440 cc bosch injector
-full no cat exhaust Miltek 2.5"
-Front mounted intercooler
-Lc-1 innovate wideband gauge w boch sensor.
-Air intake kit
-Alloy dump valve
-0.7 bar waste gate
-Homemade housing 3" MAF/fresh air intake
-"BRC" sequent LPG system with yellow big injector
My shopping list:
1 x Assembled v3.6 controller
1-wire interface no
EGT input 1
Flyback 30V flyback
ignition driver 4 + 4
Knock input channels 2
LCD connection no
MAP connection 300 kPa simplenipple
mounting-style screws
primary_trigger EC36/27 VR
PS2 connection no
secondary_trigger HALL
withSDcard no
At this time the car is running with Vems but have some issue to fix on my config:
Enable the secondary trigger
Find the right adjustment for the req-fuel/inj. voltage compensation
It seems that Boost solenoid don't work,to check...
All your advice (wiring diagrams,pictures,links,etc..)will be apreciated, thank you.
Michele.
E-mail adress: fb202535@skynet.be
Back soon with Vems config.
For the newbie!!
I just want to tell how much is important to read all the instruction,and swim into the wiki docs and advice and listen well and follow the experienced Guys like ROB,Mattias,Gintks and sorry for the other I've forgotten ;-)....
By the way they helped me I think they knows this device better then nobody and they know what they are talking about.
Read the more as you can in the forum before asking questions,frequently the answer is already there....
Hi everybody ,
I’m back with a brand new board(I ‘ve burned the first one :Newbie bad manipulation),but before mounting it again on my bi-fuel car(GPL) there is a very strange issue on my car that I need to fix:
When I drive all the time on petrol fuel,the car always start like a charm on the first engine revolution.
But when I turn on the LPG system (the engine swap automatically from petrol to Gaz )and drive the car on LPG mode,the starting moment become a nightmare,I have to try 2 or 3 time before it start.
Info :
The car always start on petrol mode
The LPG device is fully sequential “BRCsequent ” injection type
Start on fuel and turn it over to LPG when it runs.
All LPG cars in holland start on petrol and turn after 3sec to LPG.
Some links
I'm so happy because I'm running all day long with the Vems Ecu!
I can switch from Gpl to petrol and everythings works.
No starting issue!
Please share your vemscfg (or vemslog) so we can give better recommendations.
Now what I have To Do is:
- Enable the "config switch" for the different fuel type
- Fine tune for the Idle PID config
- Find the right signal for the tacho(RPM)and for that I REALLY NEED HELP,PLEASE !!!!!
- often EC36/4 p259/0 is pulled up with 1k to +12V, and selected as tach output. Other output can be selected as well (a free IGBT power ignition output).
- in rare cases, for old factory-distributer engines an [inductor] was needed to make 100+ Volt spike for the factory tachometer (than only IGBT output can be used). Normally not needed since 1988
- Cut the A/C when WOT
- Enable the Knock ignition retard function (not easy!!)
All suggestion will be appreciate....
_____________________________________________________________________________________________________________________________________________
Next step :drive my LPG injector directly by the VEMS ecu....
I'm going to drive those LPG injectors directly from the Vems ecu using 4 of the 8 injectors outputs .
here is what I will try to do:
-Start with a "4 channels LOW Z onboard extension" for the low impedance LPG injector(~ 2.3 Ohms)on the A,B,C,D output.
-Wiring the petrol injector (high impedance)to the others outputs E,F,G,H.
-With the swapping MAP function I would like to drive these differents fuels using a specific config for each one.
I await your opinions and feedback, advice as well.
- see my page