The marine plug will be wired as follows:
| Function | EconoSeal pin | Harness Colour | Chassis Plug |
| Sensor power 5V | 36-28 (+5V to sensors) | Orange | 2 (orange) |
| Sensor ground | 36-26 | Black | 1 (black) |
| Power ground | 36-5 | brown (chassis) | |
| Power ground | 36-21 | brown (chassis) | |
| Power ground | 36-32 | Black (chassis) | |
| Flyback | 36-23 | green | 17 |
| Inj common +12V | 36-25 | 3 (red) | |
| injector 1 | 36-7 (Injector A) | Red (black) | 4 (red) |
| injector 2 | 36-19 (Injector B) | gray | 5 (gray) |
| injector 3 | 36-8 (Injector C) | Purple (black) | 6 (purple) |
| injector 4 | 36-20 (Injector D) | yellow | 7 (yellow) |
| CLT | 36-14 (CLT Coolant Temp) | white | 18 (white) |
| IAT | 36-2 (Intake Air Temp) | Pink | 19 (pink) |
| TPS | 36-1 (TPS signal) | Green (black) | 20 (green) |
| MAP | 18-6 | pink (black) | 21 |
| crank position sensor | 36-27 (Primary Trigger) | Blue | 22 (gray) |
| cam position sensor | 36-13 (Secondary Trigger) | Purple | 23 (purple) |
| knock signal | 18-3 | gray shielded (red) | 24 |
| knock ground | 1 (black) | ||
| iac | 36-34 Coil #2 | orange (black) | 12 (red blue) |
| Oil pressure | cluster light | ||
| reverse lights | chassis electrical | ||
| turbo bulb on dash | 36-24 (Coil #6) | chassis | |
| CEL bulb on dash | 36-10 (Coil #7) | gray | chassis |
| Coil common | 3 (red) | ||
| coil1 | 36-35 (Coil #0) | lt brown | 8 |
| coil2 | 36-33 (Coil #1) | brown | 9 |
| Cluster RPM Gauge | 36-12 (Coil #5) | gray | Chassis electrical |
| baro | 17 | ||
| boost solenoid | 36-36 (Coil #3) | gray (black) | 10 |
| cooling fan | 36-11 (Coil #4) | pink (black dots) | 11 |
| Fuel Pump Relay | 36-15 | light Green | Chassis electrical |
| nernst_cell | 18-13 | blue | WBO2 connector |
| heater - | 18-18 | white | WBO2 connector |
| pump - | 18-7 | yellow | WBO2 connector |
| pump + | 18-9 | green | WBO2 connector |
DB15 LCD & extras config:
I am using a DB15 plug to connect a Noritake CU20045SCPB-W5J and any extras to the vehicle wiring harness.
| JP_LCD | DB_15 | Signal | Cable Colour | LCD Pin | LCD Signal |
| 2 | 1 | GND | Black(2,3,4) | 1 | GND |
| 10 | 2 | VCC | Orange | 2 | VCC |
| 3 | NC | ||||
| 1 | 3 | RS | Yellow | 4 | RS |
| 7 | 4 | RW | Red | 5 | R/W |
| 8 | 5 | Latch | Blue | 6 | E (RD) |
| 7 | DB0 | ||||
| 8 | DB1 | ||||
| 9 | DB2 | ||||
| 10 | DB3 | ||||
| 6 | 6 | Databit4 | Black(1) | 11 | DB4 |
| 5 | 7 | Databit5 | Green | 12 | DB5 |
| 4 | 8 | Databit6 | Violet | 13 | DB6 |
| 3 | 9 | Databit7 | Brown | 14 | DB7 |
Keyboard connection
| JP_PS1 | DB_15 | Signal | Cable Colour | PS/2 Pin |
| 1 (top) | 10 | VCC | gray | 4 |
| 2 | 11 | GND | white | 3 |
| 3 | 12 | Data | Lt Blue | 1 |
| 4 (bottom) | 13 | Clock | Violet | 5 |
Distributor Wiring
| Distributor Pin | Factory Colour | Signal |
| 1 | Black / Lt Green | GND |
| 2 | White / Red | +12V |
| 3 | Pink / Black | Trigger 1 |
| 4 | Yellow / Blue | Trigger 2 |
TPS Wiring
| TPS Connector Pin | Factory Colour | Signal |
| 1 | Lt Green / RED | GND |
| 2 | Lt Green / White | TPS Signal |
| 3 | Red / Yellow | NC |
| 4 | Black / White | +5V |
When fed with 12V the trigger2 outputs 5V or 0. Great for the hall trigger setup. Thanks again to Fero. When the crank trigger is hooked up to the board it measures about 3.8v and 150mv.