History of MembersPage/Sascha/BMWEthirty
Older Newer
2010-02-16 16:57:52 . . . . MembersPage/Sascha [Update issue... prob. solved.]
2010-02-12 12:26:16 . . . . MembersPage/GergelyLezsak [dwell timing ok?]
2010-02-11 14:14:46 . . . . MembersPage/Sascha [Stumble @ 2200RPM after upgrade to 1.1.63?? ]
2010-02-11 13:55:07 . . . . MembersPage/Sascha [Stumble @ 2200RPM after upgrade to 1.1.63?? ]
2010-02-11 12:53:56 . . . . mail.scmgroupcanada.com [Stumble @ 2200RPM after upgrade to 1.1.63?? ]
2010-02-11 12:53:19 . . . . mail.scmgroupcanada.com [Stumble @ 2200RPM after upgrade to 1.1.63?? ]
2008-10-30 09:11:18 . . . . MilanaPerisic [same problem]
2008-10-19 16:24:24 . . . . MembersPage/Sascha [reply to FERO]
2008-10-19 16:21:32 . . . . MembersPage/Sascha [reply to FERO]
2008-10-19 15:58:26 . . . . dsl51B63A90.pool.t-online.hu [answer by Fero]
2008-10-18 17:26:30 . . . . MembersPage/Sascha [injector drivers blowing - reply to FERO]
2008-10-18 06:54:33 . . . . 194.88.59.2 [help by Fero]
2008-10-18 03:42:13 . . . . MembersPage/Sascha [help injector drivers blowing again :(]
2008-10-08 03:08:37 . . . . MembersPage/Sascha [update on injecter driver issue]
2008-10-08 02:15:20 . . . . CPE00068c1a2eb1-CM001ade8452a2.cpe.net.cable.rogers.com [update on injecter driver issue]
2008-09-22 12:35:49 . . . . MembersPage/Sascha [Reply to FERO about inj drivers blowing..]
2008-09-22 08:17:07 . . . . 194.88.59.2 [help by FERO]
2008-09-22 00:59:13 . . . . MembersPage/Sascha [Another INJ driver blew up... please help]
2008-09-20 01:31:36 . . . . CPE00068c1a2eb1-CM001ade8452a2.cpe.net.cable.rogers.com [might have been the flyback]
2008-09-19 08:23:49 . . . . MembersPage/GergelyLezsak [your flyback ok?]
2008-09-18 14:19:36 . . . . 24.114.234.1 [inj drivers randomly blowing please help]
2008-06-30 18:26:00 . . . . MembersPage/Sascha [cleaned up BMWEthirty page]
2008-06-30 18:25:14 . . . . MembersPage/Sascha [cleaned up BMWEthirty page]
2008-06-07 09:34:11 . . . . MembersPage/Sascha [added dyno sheet for turbo E30]
2008-05-26 05:03:18 . . . . MembersPage/Sascha [added pic of cam sync, more to follow]
2008-05-26 05:01:33 . . . . MembersPage/Sascha [added pic of cam sync, more to follow]
2008-05-24 14:32:31 . . . . CPE00068c1a2eb1-CM001ade8452a2.cpe.net.cable.rogers.com [Added updates for BMW, new harness, new options, motor is now turbo]
2007-10-14 14:16:29 . . . . MembersPage/Sascha [Added new project basic information]


Changes by last author:

Added:
Will upload the config later today... I do not have any logs @ this time... Had to revert to 1.0.73 to make the car drive properly. Possibly could attempt to go back to 1.1.63 on the weekend for logs.
Changed:
* Check your dwell timing. If you use more than available for a given rpm that will cause similar problems. (And it was not the case with older firmwares). 2200rpm is a bit low for this, however, worth a check.
*Check your dwell timing. If you use more than available for a given rpm that will cause similar problems. (And it was not the case with older firmwares). 2200rpm is a bit low for this, however, worth a check.

**I checked dwell timing and played around with it... didn't help... what I believe did solve the issue was setting the angular width of tooth setting under primary trigger settings. For some reason after the upgrade it was 386 and not 6 like it was supposed to be/was. Seems like that fixed the issue.

Deleted:
Will upload the config later today... I do not have any logs @ this time... Had to revert to 1.0.73 to make the car drive properly. Possibly could attempt to go back to 1.1.63 on the weekend for logs.