History of MembersPage/RijaRobinson
Older Newer
2018-12-18 11:35:37 . . . . 77-234-77-219.pool.digikabel.hu [subpage for S85B50]
2018-12-18 11:28:09 . . . . 77-234-77-219.pool.digikabel.hu [DO measure input DC voltage with input open and with 1k..]
2018-12-13 13:32:05 . . . . l9.lns-se1200-ld-01-t2-31-35-240-216.dsl.dyn.abo.bbox.fr [P259 test]
2018-12-13 11:53:33 . . . . 62-165-252-229.pool.digikabel.hu [add EC10 page]
2018-12-13 10:50:31 . . . . 62-165-252-229.pool.digikabel.hu [link dual WBO2 and LSU4.2 / LSU4.9 notes]
2018-12-13 10:27:16 . . . . 62-165-252-229.pool.digikabel.hu [internal pullup measurement with 1k to GND]
2018-12-13 10:15:19 . . . . static.kpn.net [added additonal email info, reviewed case and suggested action]
2018-12-11 13:00:44 . . . . l9.lns-se1200-ld-01-t2-31-35-240-216.dsl.dyn.abo.bbox.fr [s85 new page]
2018-02-06 12:58:09 . . . . catv-86-101-250-44.catv.broadband.hu [mixed projects page: splitting subpages S50B32]
2014-09-22 12:38:03 . . . . catv-80-98-222-153.catv.broadband.hu [camshaft angle control hints]
2014-09-21 06:11:58 . . . . sto95-5-78-237-254-60.fbx.proxad.net [trigger log]
2014-09-12 20:55:56 . . . . sto95-5-78-237-254-60.fbx.proxad.net [M5 V8 PROJECT]
2012-12-22 14:05:02 . . . . TrifanCatalin [Wrong pin usage]
2012-09-19 14:58:47 . . . . adsl6-223.pool.businesstel.hu [lower measure tooth so measured position gets lower]
2012-09-19 11:24:15 . . . . adsl6-223.pool.businesstel.hu [lower measure tooth by at least 4]
2012-09-16 16:22:46 . . . . alf94-10-82-243-46-114.fbx.proxad.net [Outputs test]
2012-09-03 15:39:08 . . . . adsl23-49.pool.businesstel.hu [quick output tests]
2012-09-02 12:05:42 . . . . adsl23-49.pool.businesstel.hu [vanos oilpressure, and all 4 outputs info ?]
2012-08-31 10:58:09 . . . . alf94-10-82-243-46-114.fbx.proxad.net [logfile]
2012-07-24 22:56:26 . . . . alf94-10-82-243-46-114.fbx.proxad.net [vanos issue]
2012-07-24 22:52:01 . . . . alf94-10-82-243-46-114.fbx.proxad.net [vanos issue]
2012-07-18 00:15:03 . . . . catv-89-133-73-126.catv.broadband.hu [Vanos preamble]
2012-07-14 13:47:18 . . . . adsl35-127.pool.businesstel.hu [possible ]
2012-07-14 13:24:19 . . . . adsl35-127.pool.businesstel.hu [just test the 4 PFET outputs and make ]
2012-06-23 09:46:27 . . . . alf94-10-82-243-46-114.fbx.proxad.net [Vanos control]
2012-06-16 18:52:30 . . . . alf94-10-82-243-46-114.fbx.proxad.net [Trigger ]
2012-06-16 11:46:02 . . . . alf94-10-82-243-46-114.fbx.proxad.net [engine specs]
2012-06-16 11:38:49 . . . . alf94-10-82-243-46-114.fbx.proxad.net [typing mistake]
2012-06-16 11:29:11 . . . . alf94-10-82-243-46-114.fbx.proxad.net [BMW M3 s50b32 Turbo Dual Vanos]


Changes by last author:

Added:
Separate pages for each project (and subsystem of special interest, or in case of problem.). Mixing 2(or more) projects on 1 page is confusing, and NOT supported.
Added:
* MembersPage/RijaRobinson/BmwSEightyfiveBfifty S85B50
Deleted:
--------------------------------------------------------------

S85B50

My new project is a s85b50 engine from e60 M5.

ECU is V3 with internal CAN

Engine has can bus controlled throttles

First issue: Primary trigger is VR is not detected (not seen in triggerlog and RPM=0).

Ground point is bolt on the chassis. Strongly tightened.

The 4 cam signals are all ok.

Info provided by email:

* Everything is working except Primary trigger VR signal.

** maybe ECU is configured as primtrig HALL for some reason ? can you measure input DC voltage with 1k resistor between ground and EC36/27 ? >0.5V (1.35V typically for 2k7 internal pullup) likely HALL input. Measuring <270 mV means weak internal pullup (likely VR), perhaps p259 damaged causing VR not sensed ?

* I have a spare Ecu to test the same trigger on the same harness and it sees the primary signal.

* All the 2nd 3rd 4th and 5th signals are seen on the triggerlog but the 1st.

** Double-check grounds just in case, and see [repair/upgrade]

* I have an engine simulator also to test and the same thing happens.

* The spare ecu is OK.

DB review and feedback

* If the ecu was ordered with pri = VR and 4x HALL (for cam triggers) than it should just work out of the box

* Your other testing (with the other ecu and engine simulator) suggests its not a problem with wiring or sensor, this must be some ecu mis-configuration.

I have checked P259 channels 4,5,6,7 making vanos solenoids ticking. They work.

I assume p259 is not dead.

I can also simulate Hall sensor signal with the Jimstim but prim signal still missing.