VEMS Home Products Documentation Wiki Webstore
WikiHome ProjectPage DocsPage UnderDevelopment MembersPage SiteIndex RecentChanges Preferences
History of LoloQuattro
Older Newer
2013-06-24 18:10:18 . . . . catv-80-98-222-153.catv.broadband.hu [check the paper, or inputs can be tested easily]
2013-06-23 18:23:01 . . . . lis91-2-88-164-215-166.fbx.proxad.net [Is there already two extra analogs input on motronic55 vems 3B ?]
2013-06-01 07:48:29 . . . . netacc-gpn-4-137-27.pool.telenor.hu [AAN => 3B ignout]
2013-05-29 15:07:30 . . . . catv-80-98-222-153.catv.broadband.hu [Updated with description and image]
2013-05-29 14:13:04 . . . . catv-80-98-222-153.catv.broadband.hu [Added analog input instructions]
2013-05-29 10:49:21 . . . . LoloQuattro [Question on the change from Audi AAN 5 coils vems.cfg to 3B 1 coil vems.cfg]
2013-05-27 22:42:33 . . . . catv-80-98-222-153.catv.broadband.hu [note about 3B and AAN harness]
2013-05-24 16:20:49 . . . . lis91-2-88-164-215-166.fbx.proxad.net [modifications for the conversion from motronic55 v3 vems from Audi ADU, ABY or A]
2013-05-24 16:00:14 . . . . lis91-2-88-164-215-166.fbx.proxad.net [What modifications for the conversion from motronic55 v3 vems from Audi ADU, ABY]
2013-05-24 15:50:04 . . . . lis91-2-88-164-215-166.fbx.proxad.net [What changes in the config to convert a motronic55 v3 vems from Audi ADU, ABY or]
2012-02-07 15:04:26 . . . . GergelyLezsak [upload to anywhere or filearea]
2012-02-07 09:23:32 . . . . LoloQuattro [Audi bad cold start answer]
2012-02-06 14:24:06 . . . . GergelyLezsak [give more details]
2012-02-03 14:21:14 . . . . LoloQuattro [Audi RS2 very bad cold start]
2012-02-03 13:08:08 . . . . LoloQuattro [start when warm and idle from 2000rpm to 950 solved thanks]
2012-01-24 17:34:46 . . . . 83-172-85-14.sheab.net [answers]
2012-01-24 12:55:43 . . . . LoloQuattro [Response to Erikk for his answer to Audi RS2 very bad start when cold]
2012-01-24 12:39:48 . . . . LoloQuattro [complement info about the Audi RS2 bad cold start]
2012-01-24 09:43:45 . . . . proxy31.netz.sbs.de [Answer to cold start problems.]
2012-01-24 09:08:57 . . . . LoloQuattro [Cold start]
2012-01-24 08:48:44 . . . . LoloQuattro [presentation member page]

Changes by last author:

Changed:

many thanks.

Lolo

* Can you check the paper that came with your ECU ? That is the best source, as your device might be different from default if ordered with special specs

** especially for 3B with SSC6 which has different best set of pins depending on circumstances

** especially that this very controller was modified later, AFAIK

* if the paper was lost, you can also test easily. Take a 1kOhm resistor and pull the pin in question (from SSC6) to GND, than to +3..5V. Watch the "analog inputs raw" gauge-group during this.

** that is safe to any pin of the extra connector SSC6 (or econoseal10 in newer devices) even if it's not analog input. Just do not apply more than 5V ( >5V would be damaging even through a resistor)