####   
 #    #  
 #       
 #    #  
  ####   
         

 _       _ 
( )  _  ( )
| | ( ) | |
| | | | | |
| (_/ \_) |
`\___x___/'
           
           

  ____  
 | __ ) 
 |  _ \ 
 | |_) |
 |____/ 
        

 _       
( \      
| (      
| |      
| |      
| |      
| (____/\
(_______/
         

         
         
  #####  
 ##  ##  
 ##  ##  
  #####  
     ##  
     ##  

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
*MembersPage/Norbitron/Opel Opel Astra G OPC, ETC+Tempomat *[http://www.vems.hu/wiki/index.php?page=MembersPage%2FNorbitron%2FAudina Audi 1.8 8V] *[http://www.vems.hu/wiki/index.php?page=MembersPage%2FNorbitron%2FAudit Audi 1.8 16Vt] *[http://www.vems.hu/wiki/index.php?page=MembersPage%2FNorbitron%2FAudinv Audi V8 3.6 Turbo] * MembersPage/Norbitron/VemsEcuNarrowbandOxygenOutput *[http://www.vems.hu/wiki/index.php?page=MembersPage%2FNorbitronAudiAanSixty Audi AAN 60-2] *[http://www.vems.hu/wiki/index.php?page=MembersPage%2FNorbitron%2FAudiV Audi 4.2 32V with auditrigger] *[http://www.vems.hu/wiki/index.php?page=MembersPage%2FNorbitron%2FMultip Analog input multiplexer] *[http://www.vems.hu/wiki/index.php?page=MembersPage%2FNorbitron%2FAstrag Astra G ECU rebuild] *[http://www.vems.hu/wiki/index.php?page=MembersPage%2FNorbitron%2FVectra Vectra C20let] *[http://www.vems.hu/wiki/index.php?page=MembersPage%2FNorbitron%2FETC ETC Problem] *[http://www.vems.hu/wiki/index.php?page=MembersPage%2FNorbitron%2FMSIXTY BMWV8] *[http://www.vems.hu/wiki/index.php?page=MembersPage%2FNorbitron%2FEGT 5xEGT+ETC AUDI AAN] *[http://www.vems.hu/wiki/index.php?page=MembersPage%2FNorbitron%2FEgt EGT] *[http://www.vems.hu/wiki/index.php?page=MembersPage%2FNorbitron%2FCAN CANBUS] *[http://www.vems.hu/wiki/index.php?page=MembersPage%2FNorbitron%2FTrig Trigger] *[http://www.vems.hu/wiki/index.php?page=MembersPage%2FNorbitron%2FTrigvrsix VRsixTrigger] *[http://www.vems.hu/wiki/index.php?page=MembersPage%2FNorbitron%2FLsthree Ls3] * MembersPage/Norbitron/LotusEsprit - extrapulsse 6+1 trigger ---- 2016.10.25 '''Q''': Is the Shift-cut analog input working in inverted mode? The car has a clutch switch wich is normaly in closed position. When the pedal pushed down the button open the circuit. I know it wasn't working with old firmware. '''A''': No, inverted shiftcut input channel selection is not supported; Nor is it needed as there are two activation thresholds so any switch can already be used. I see the inverted channels are mistakenly available in the shiftcut input selection list for 1.2.36 and above those will be removed shortly. Best regards, Dave ---- 2014.08.29 Opel Astra Z20LEH ETC controlling problem. http://www.vems.hu/files/Norbitron/v3.3_u009457-2014.08.29-13.06.32.vemslog I configured the PPS1, PPS2, and (manualy)TPS1, TPS2 sensor. It's working fine, however the TPS does not react to PPS. I've tried to change the duty cycle from 0 to 100% without any success. The bridge is always grounded, if ETC is disabled then the bridge does PWM just fine. Also if ETC is disabled and injector pwm is set to between 50% - 100% the TPS reacts to the changes. In the log the ETC didn't working. I moved to manualy. Answered related bug report: http://vems.hu/vemstune/sharingcenter/reports.php?cmd=view&key=bXF20M - DB If ETC target cannot be reached in 1.2.20-1.2.28 with an assumedly reasonable config (actuator min/max not reached; P and I nonzero, ...), please see newest from [http://svn.x-dsl.hu/f/EXPERIMENTAL/ dirX] or [http://svn.x-dsl.hu/f/ dir] and test with that (wider window for ETC integral limit), and report result. .... 2014.01.31 Which is the best choice to triggering the AAN engine? I don't like to use auditrigger. I would like to use more reliable way for it. 60-2 missingtooth wheel, 5pin coiltype or other tip from you? /Norbitron I use 60-2 with Hall-sensor, running 5coils without camsync. Works perfect. / Erik Englund -What kind of hall sensor do you use? Is it? -> https://shop.vems.hu/catalog/hall-sensor-p-107.html?osCsid=310abb9cb34c2b8a185f5de1405cc8ce This isn't recommending with home made 60-2 wheels. Do you use an OEM from other car? /Norbitronic .... 2013.12.21. Audi Coupe 2.2 20VT AAN - Primary trigger modification note. Changed from the original 3 trigger to 2 (TDC,CAM). Don't use the 135teeth RPM trigger. Originally the TDC- sensor are sensing 1pin. We installed more 4 pin so there are 5pin every 72degree back of the flywheel. !!!I've had CHANGED THE PRIMARY SENSOR POLARITY!!!
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.