__          __
 \ \        / /
  \ \  /\  / / 
   \ \/  \/ /  
    \  /\  /   
     \/  \/    
               
               

         
 ##      
 ##      
 #####   
 ##  ##  
 ##  ##  
 #####   
         

   ____  
  / __ \ 
 | |  | |
 | |  | |
 | |__| |
  \____/ 
         
         

         
         
 ##   ## 
 ## # ## 
 ####### 
  #####  
  ## ##  
         

  ______
 |___  /
    / / 
   / /  
  / /__ 
 /_____|
        
        

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Staging related setup for MembersPage/NanassyPeter/CloneInstall''' TODO: move (and cleanup) any staging notes from MembersPage/NanassyPeter/CloneInstall/Trigger because it will not be answered there the car has two completely separate fuel lines,with the same componenets,so the injectors are the same in the two groups (higZ,14ohm). ---- Initial try First i will try with 2 injectors per cylinder as on MembersPage/NanassyPeter/CloneInstall/Wiring, wired together driven by 5 FETs. It worked initially, but (surprisingly) with warm engine, it goes rich and doesn't seem easy to tune. ---- StagedInjection: First group will run sequentially (on 5 FETs),valve timed, the second group (on 1 IGBT) will switch right after when there is a slight amount of injection time, say after 100kpa or so. * Rate according to Marcell is 128 or 50% * point (threshold) of switchover is ... See GenBoard/Manual/DigitalOut/Table for ECxx pins (TODO: update here for complete verification) * Primary set ** connected sequentially to A,B,C,D,E * Secondary set ** connected grouped to (F,F,F), (G,G) ** connecting 3 in parallel is no problem, because injectors are 12..14 Ohm high-Z ** the injector-closing (flyback voltage on powerflyback) is same no matter if 2 or 3 injectors are connected to a given channel. With 3 channels, there is no risk of ruining the output with high-Z (3A load current vs. 9A capability; 3A flyback current vs 4..9A capability - capability depends on pwm-ing configuration) ** 5 injectors (even of the staging set) to 1 INJ channel is not recommended. *** if you configure h[0] to inject together with the primary set (eg. as an experiment to find the equivalent pulsewidth: eg. 3.3 msec with both sets of equal size running is equivalent quantity as 6 msec of the primary set only) => the supply rail will fluctuate more, and fuel quantity will not be as even as with 2+3. *** If you wire 2+3, you can still easily apply both banks connected to same output if you badly need the output channel in the future. * This way H FET (EC36 pin 17) is reserved for something, maybe ALS air-solenoid ? ** not badly needed for anything else, since even with 5 transformer + COP ignition, there are 3 free IGBT-s to drive fuel pump relay and such That, with (360 degrees rotated) 53124 firing order means firing 10,04,01,02,08 that written reverse is h[0]=08 02 01 04 10 .. .. .. and with the staging F (20) and G(40) driven together (in last position, that is position 7) it becomes <code> h[0]=08 02 01 04 10 80 00 60 </code> that is 8 2 1 4 16 128 0 96 decimal (as in MegaTune) The 80 (decimal 128) mask in position 5 is useful so the inj H FET can be configured (eg. for driving ALS kicker valve) with ..channel=50 (in MegaTune, output to injFET-5 or injgroup-5) ---- Old Q was: After instaled the stable working trigger,we tried to start tuning the car,just for basics,cranking and idle,and low load and low rpms.I realized real fast that there is a problem with the fuel map,or with the whole fuel system,because after the engine completly warmed (90C CLT),i had some really annoying richening.With the same setting just before this (with idle lambda 0.95) it now idled at 0.74,which is unacceptable by any means.I tried to decrease the fuel map there (VE),wnd it leaned out,but after 5-15 secs it richened up again right there where i leaned out.For the time being i disconnected the second fuel rail. We still have some mechanical issues with the engine very little fuel leak thermostat wont open alternator wont work but these will be solved very soon. Every basic ECU sensors installed TPS is working now0-100% MAT is connected (reading 7C more than real) ---- '''TODO: cleanup according to above''' - it seems all is answered above Fuel staging How can i set up the unused (INJ 7,6,5) fets to drive the staged ones?I read the relevant page,do i have to insert them in to h(0) tables last place?my current h0 looks like this h(0) 4 16 8 2 1 0 0 0 so the staged with 1 inj fet (INJ6) h(0) 4 16 8 2 1 0 0 32 and if 2 used (INJ6>3 injectors,INJ7>2 injectors) h(0) 4 16 8 2 1 0 0 (32 64) OR (32+64=96???) rotating the injection phase (this table is 288 degrees earlier compared to the 8 2 1 4 16 ... above) shouldn't make a big difference (at the end of the tuning! it effects the best VE table slightly), so leave it the way you had when you tuned
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.