___   
(  _`\ 
| |_) )
| ,__/'
| |    
(_)    
       
       

  ___  
 / _ \ 
/ /_\ \
|  _  |
| | | |
\_| |_/
       
       

         
|\     /|
| )   ( |
| (___) |
|  ___  |
| (   ) |
| )   ( |
|/     \|
         

 _______ 
(  ____ \
| (    \/
| (__    
|  __)   
| (      
| (____/\
(_______/
         

         
 ####### 
 ##  ##  
    ##   
   ##    
  ##  ## 
 ####### 
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
M117 5.6L even-fire V8 engine, Mercedes 560SEL model 1990 and 1991 (2 engines, 2 harnesses, same specs, theoretically) Trying to assemble the puzzle... As I understand (orig info "quoted") * Ordered 2 kits from [http://elbe.ee/products/efi-kit/ Hendrik] ** "The only problem we had when we install the kit is idling." * '''originally both were running''' (with 1 or 4 ignoutputs ? 4 ignoutputs correct ?) * ignition was changed from EC36/pin36 to EC36/pin11 while the engine was running => ECU damaged * The other engine was also running, but idle was not tuned ** tuning the idle can be done locally, not by sending the ECU to another continent. ---- '''Wiring''' * [http://www.vems.hu/files/MembersPage/Mercedes/Mercedes_SEL_M117_5.6L/elbe_efi_kit_wiring.pdf original harness.pdf] (the only thematical information received, might not be uptodate, see ignition and IAC. Anyway '''keep the pdf open while viewing this page''' ) ** beware that IGN1 .. IGN8 numbering in this pdf is non-standard (subtract 1. The EC36/.. pin should be authoritive) ---- '''Ignition''' Firing order : ... ? Note: All ignition wires lack fuses (there is only 1 10A fuse in the whole harness, zzz... Not good, must be added). * "We did all the installation as Instructed but unfortunately while the engine was running the main 12v wire was shorted and the ecu burn" * "We '''changed one of the ignitions outputs from 35 to 11''' as Elbe instructed and run again but there was a smoke and one of chips was smoking and fire" * "The other ecu it was a mistake changing the ignition while engine running" ** you mean "changing ignition output in config" while engine running ? Or changing the wiring somehow ? (usually difficult with EC36 plugged in, but who knows :-) ** was it reconfigured in the "ignition outputs" dialog that starts with red "Must not be changed with running engine" ? ** You made a video of the IGBT smoking (apparently the full event, from the beginning)... What is the history of that ? It almost seems like you were prepared for the smoke. Just curious Originally as in the pdf, later Changed to ... (information from Waleed, no EC36/pin.. reference) Red is +12V. * EC36/35 (ignch0) Yellow (cylinders 1 and 6) ** changed from EC36/pin35 to EC36/pin11 (ignch4) ? * EC36/33 (ignch1) Green (cylinders 5 and 3) * EC36/34 (ignch2) White (cylinders 4 and 7) * EC36/36 (ignch3) Blue (cylinders 8 and 2) ** note to installers: using ignch0 and ignch1 will work with a VEMS ECU with 6 or 8 IGBTs, it is smarter to allocate ignch 2,3,6,7 so it could also work with just 4 IGBTs (GenBoard/Manual/IgnitionOutput). Opel P/N - [http://www.aliexpress.com/item/Free-Shipping-High-Quality-For-Opel-For-Vauxhall-Ignition-Coil-Oem-1208065-0221503001-90443900-90449572-Dmb410/2000076237.html 1208065] * these are '''2x2 passive wasted spark ignition transformers''' (with 3-pin AMP connectors, suitable for inductive ignition, and quite rugged for the 25..45USD price, reliable, also easy to replace) ** so obviously 2 modules are used ** fuses should be used, 3A or 4A for each ignition output (4 ignfuses total). Change to 5A after engine is tuned, and all is well. ** dwell probably 3msec ---- '''IAC''' Can you detail your Idle air control setup ? Is it PWM type? * Measure resistance, * take note of partnumbers. * Did it react to openloop changed during initial testing ? Why are there so many IAC pins in the kit wiring pdf ? * EC36/pin12 (ignch5) Brown for "M117 kit" * EC36/pin24 (ignch6) (M117/M103 kit, but no color in the pdf). What does this mean ? ** What are the actual IAC pin from the ECU ? ** (of course the IAC also has a +12V side, hopefully through a 4..5A fuse) ---- '''Config''' * [http://www.vems.hu/files/MembersPage/Mercedes/Mercedes_SEL_M117_5.6L/MercedesSEL_M117_5.6L_Saudi_ignitionMessed.vemscfg original vemscfg] (ignition should be compared to above) ** do you happen to have running vemslog ? (when tuning idle, it makes sense to capture vemslog for later analysis) * any validation errors ? ** suspicious things ? ** recommendations ? ---- '''Trigger''' Primary trigger: EC36/pin27 VR or HALL ? * 60-2 ? Secondary trigger: EC36/pin13 HALL * 1 pulse per 720 crankdeg, right ? Any triggerlog captured available for verification ? ---- Unrelated: * see FileArea to upload image, vemslog or zip files
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.