Editing MembersPage/JoseLCortes

 _    _ 
| |  | |
| |  | |
| |/\| |
\  /\  /
 \/  \/

 _ 
(_)
| |
| |
| |
(_)

 __     __
 \ \   / /
  \ \_/ / 
   \   /  
    | |   
    |_|

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.

Visit Preferences to set your user name
Summary of change:
I have used motec on GSXR1000 last year in a team which I had worked in. Motec M-800 is great but it is expensive. Genboard seem to have same or superior hardware specifications. http://www.nmine.com/msavr/newmironly.jpg '''NEW, Motuner ecu tuning software''' MembersPage/JoseLCortes/Motuner '''Genboard Racing Functions''' MembersPage/JoseLCortes/GenboardRacingFunctions '''GSXR1000RK3 Engine Sensors Description''' MembersPage/JoseLCortes/EngineSensorsDescription '''Ignition timing accuracy test with Genboard_v3/Firmware2004-11-24_v11_2''' MembersPage/JoseLCortes/IgnTimingAccuracy '''My engine started with Genboard working in fully sequencial ignition (with COPÂ´s)!!!''' MembersPage/JoseLCortes/FullySequencial '''Motorcycle Engine eddy current dynamometer''' MembersPage/JoseLCortes/EngineDynamometer --------------------------------- The R1 engine is here! ||http://www.nmine.com/msavr/122_2281p.jpg||http://www.nmine.com/msavr/122_2289p.jpg|| ||[http://www.nmine.com/msavr/122_2281.jpg 122_2281.jpg]||[http://www.nmine.com/msavr/122_2289.jpg 122_2289.jpg]|| Our mision is to install a Motec, but I hope to get install and test genboard in this engine, it is completely new engine, from a absolutely 0 km motobike!!! --------------------------------- '''First cycle strange firing sequence report 17-October-2005 ''' --------------------------------- The first turn during crancking seems to apears strange firing sequence it makes a ugly explosions during start process and dificult the starting process. I have checked that it is not a ground loop or any electromagnetic noise. (in fact, now i am testing it with a simulator) * latest firmware version used: v3_firmware_1.0.18 * http://www.nmine.com/msavr/config.txt (updated 17-10-2005) * http://www.nmine.com/msavr/tables.txt (updated 17-10-2005) *h[2]=03 02 01 00 03 02 01 00 ---- The above config file has some questionable settings, this is what I came up with for that engine: tooth_wheel=07 # 8-1 teeth trigger_tooth=01 another_trigger_tooth=04 crank_minper=40 # FF is too high, FF would cut spark at high-RPM tooth_wheel_twidth1=0A #decimal 10: 45 degrees (0-720deg = 0-160 fake degrees) tooth_wheel_twidth2=14 #decimal 20: 90 degrees. This assumes reset_engphase_after (720 degrees) is decimal 160 (hexa A0) cam_sync_r_edge_phase=0A cam_sync_f_edge_phase=0A reset_engphase_after=82 # ???? decimal 130 ???: The trigger tooth after the trigger tooth at 540 degrees (585 degrees) 585/720*160=130 (82hex) Why not decimal 160 ? -JÃ¶rgen ---- I have no multichannel oscilloscope so I built a "channel multiplier" with resistors: -Ign Channel 00 - 9.4k lower pulse -Ign Channel 01 - 4.7k -Ign Channel 02 - 2.2k -Ign Channel 03 - 1k higher pulse http://www.nmine.com/msavr/strange17-10-05.gif It is diferent than old testings, this time the sequence is always exacly the same. Only two ignition firings are erroneous. ----------------------------------------------- Jose L Cortes joseluis_jlc at hotmail dot com
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.