#    #  
 #    #  
 #    #  
  #  #   
   ##    
         

 _       
( (    /|
|  \  ( |
|   \ | |
| (\ \) |
| | \   |
| )  \  |
|/    )_)
         

 _   __
| | / /
| |/ / 
|    \ 
| |\  \
\_| \_/
       
       

 _____ 
|_   _|
  | |  
  | |  
 _| |_ 
 \___/ 
       
       

 ___   
|  _`\ 
| (_) )
| ,  / 
| |\ \ 
(_) (_)
       
       

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
This is my shopping list. Please tell me if you see something wrong. I have put in some chips that might not be necessary, but it's better to have some not needed than wait and pay freight for some low cost hard to get parts later. Where not mentioned, Qty is one. *GenBoard3.3 *Blue LCD *Alubos1600 case ** 6 holes *Gasket ** 2 needed, front and endplate *Endplate ** yes, available with DSUB cutouts. (I have DSUB punches [ESj]) *EC Front *3x clamping plates *VR Coil chips LM1815 ** Only one needed, one is included with the 3.3 board *2Ch Knock sensor Chip *2 Pcs. EGT Amp chip AD597AR ** Room for 2 on the board, its better to solder them both right away, even if you only need one *Opamp LT882IS ** Not necessarily needed for operation *Econoseal-18 PCB *2Pcs. Econoseal-18 Wire *Econoseal-36 PCB *2Pcs. Econoseal-36 Wire *Adressable Latch TPIC6A259DW ** One of these are installed from factory too. *Idle stepper driver SN754410 ** this is not needed for that volvo engine, it has a solenoid for idle control, not stepper (But I'll take one anyway. [ESj]) *Qty: 8 Ignition driver HGTP14N40F3VL/IRGB14L40C ** Cost isnt too high, its easier to clamp the box with all of them in place *Qty: 9 Inj/WBO2 heater driver FQPF20N06L ** support for 8 high power inductive loads, (injectors, idle solenoid etc..) and one WBO2 heater * Ignition driver insulation sheet *Power flyback,no wires *250kPa MAP sensor MPX4250AP *2 Pcs. EGT sensor K-type *4 Pcs. Hall sensor TLE4905 Unip. *K-thermocouple connector pair male+female *5Pcs.Temp. Sensor NTC 2K2 *Wideband O2 Sensor. *Wideband Connector for WBO2 sensor. *2Pcs. VEMS Sticker. Empty cart would not check out, so I had to put something in it. No additional cost to get early shipment. Just checkout ASAP. Freight cost to Norway is 5 EURO flatrate, as elsewhere. Partial shipment is OK as long as the first includes enough to get started. '''What do I do next?''' * checkout the order ** if you don't have the cart (I guess you do), you can checkout an empty cart and write this URL to the order note '''Done''' ** also, write to the order note: negotiated with Marcell: 45% "wannabe-developer" discount for genboard and 20% for other items '''Done''' ** choose "check/money-order" payment and IBAN transfer to XDSL Ltd Hungary, as on WebShop. '''Waiting for approval of amount'' I Calculated sum to pay as Eur. 635,- Please correct/approve. Payment initiated with my bank. [ESj]
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.