##    
 ######  
   ##    
   ##    
   ##    
    ###  
         

    ##   
         
   ###   
    ##   
    ##   
    ##   
 ## ##   
  ###    

 ###     
  ##     
  ##  ## 
  ## ##  
  ####   
  ## ##  
  ##  ## 
         

   ##    
    #    
    #    
    #    
    #    
    #    
   ###   
         

 _     _ 
( )   ( )
`\`\_/'/'
  `\ /'  
   | |   
   (_)   
         
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
http://www.vems.hu/files/sensors/MAP/MAP_400kPa_bare_0001_l.jpg '''MAP-board 1.0''' This adapter is used to hold the 400kPa MPXH6400 sensor. Motorola packages this nice sensor in SMD only, so a PCB was necessary for a clean install. Output is compatible with the more common MPX4250AP sensor, but '''features 400kPa range''' instead of 250kPa. Recommended for > 130kPa (1.3bar, 18psi) boost. there are some simple extras onboard, like * regulator (so it can be powered from 12V and there is a 5V output) * thermometer (Temperature output) ---- '''Pinout of the 5V version''' || '''pin nr.''' || color'''|| '''signal''' || '''range''' || '''note''' || || 1 || white || MAP output || 0 .. 4.8V || || || 2 || brown || GND || 0V || || || 3 || red || '''5V in''' || 5V || max 10mA. Useful for HALL, TPS, etc... || || 4 || blue || temp out || 0.5 .. 4.5V || NTC, similar U(T) as CLT || || 5 || - || GND internal || 0V || || || 6 || - || not connected || - || || The first 3 pin is compatible with the MPX4250AP pinout. When mounting onboard GenBoard/VerThree, for mechanical stiffness: * recommended to connect all 6 pins * some hotmelt helps for extra ruggeddness * the pneumatic tube to the frontplate also secures the mounting Mounting is normally done vertically, perpendicular to the v3.x PCB. The nipple is horizontal, points to the "VIV" type pneumatic connector mounted "through the frontplate". '''Notice that this sensor has small 5x3mm nipple, so''' * either the smaller 5x3 mm VIV connector is needed * or VIV connector that is 5x3mm on one side and 6x4mm on the other side See GenBoard/Manual/PneumaticTube ---- '''Pinout of the 12V version''' || '''pin nr.''' || color'''|| '''signal''' || '''range''' || '''note''' || || 1 || white || MAP output || 0 .. 4.8V || || || 2 || brown || GND || 0V || || || 3 || red || 5V out || 5V || max 80mA || || 4 || blue || temp out || 0.5 .. 4.5V || NTC, similar U(T) as CLT || || 5 || - || GND internal || 0V || || || 6 || grey || '''+12V in''' || 6.3 .. 16V || || '''Coming soon''': packaged versions for engine bay (eg. firewall mount) usage ---- '''See also''' * GenBoard/Manual * GenBoard/Manual/Config/ManifoldAbsolutePressure * WebShop (see Genboard, sensors)
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.