##      
 ##      
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
         

         
#### ### 
 ##   #  
  ####   
  ###    
 #  ##   
###  ### 
         

  _____  
 |  __ \ 
 | |__) |
 |  ___/ 
 | |     
 |_|     
         
         

 ___   
(  _`\ 
| ( (_)
| |___ 
| (_, )
(____/'
       
       

         
         
  ### #  
 #   ##  
 #   ##  
  ### #  
      #  
      #  

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''ISP via PC Parallel (printer) port''' Originally on MembersPage/MattiasSandgren/NickesBMW/AvrBootCode (thanks Mattias). ---- * On XP (or later mswin ?) you may have to install giveIO usually found in c:/winavr/bin/install_giveio.bat to enable direct access to the parallel port. * Command syntax : avrdude -c '''bsd''' -p m128 ... ||AVR pin command||ISP header #||Parallel port pin||Notes|| ||AVR /RESET||5||7||Yellow|| ||AVR SCK (clock input)||3||8||Black|| ||AVR PDI (RXD) (instruction in)||4||9||Red|| ||AVR PDO (TXD) (data out)||1||10||Orange|| ||Signal Ground||6||18||Brown|| * MOSI and MISO are not used. Correct pins from the schematics AVR pin 2 = RXD/PDI -> ISP header Pin4, AVR Pin3 = TXD/PDO -> ISP header pin 1 See signal functions vs header pins [http://vems.hu/download/v3/doc/assembly/cable.txt bottom: "VEMS V3 ISP pinout"] (also called "ISPI") The avrdude ''bsd'' pinout is compatible with the ''alf'' pinout (so -c alf should work just as well). The alf code also sets some status (ready, error, verification, complete ...) LEDs that can be useful for fancy geeks (although the same info is also on avrdude screen, and some in return value). This is what it looked like: http://www.vems.hu/files/MembersPage/MattiasSandgren/avr_isp_cable/avr_isp_cable_attached.jpg http://www.vems.hu/files/MembersPage/MattiasSandgren/avr_isp_cable/avr_isp_cable_ends.jpg ---- '''330 Ohm recommended on all 4 signal lines''' (or sg. between 270..348 Ohm for protection) * GND is direct wire of course ** multiple GND could be connected, pin21 on this cable. * Cable length should be 0.4m (1.2 feet) or less. * request "5..10 pieces of throughole 348 Ohm resistors" in WebShop in your order comment (best effort - provided free of charge) or add a few [https://shop.vems.hu/catalog/resistor-p-86.html 348 Ohm] to cart. http://vems.hu/download/v3/bootloader/ISP/ParallelPort_ISP_cable/DSUB25M_VEMS_genboard_v3_ISP_cable_4x330Ohm.jpg ----
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.