The VEMS Wideband & EGT Gauge is very simple to install, and will provide trouble free service for your Motorsport application when installed correctly. Please read the following document carefully and ensure that you fully understand its contents before you proceed with the installation. If you have any queries please contact your VEMS Reseller.

Gauge Installation

Wideband Sensor

Install the sensor into your exhaust using a suitable bung. If your engine already has a lambda sensor you can replace it with your new wideband sensor, and use the Gauge's Lambda output. If you do not have a suitable (M18x1.5) bung please contact your supplier for fitting advice.

Make sure that the wideband is connected to the 6 pin plug.

Power Connection

Connect the red power wires to a suitable +12v supply and the blue ground wire to a clean grounding point. You will want to use an accessory supply that provides 5amps when the ignition is on. Note that some car lighter sockets are current limited and may not be powerful enough to drive the Gauge and Sensor

Exhaust Gas Temperature Sensor

The Exhaust Gas Temperature (EGT) sensor is a K-type thermocouple it is important to note the wires colour and polarity of the wires. The green insulated wire is the positive (+) and white negative (-), it is vital that you ensure that the polarity is observed otherwise incorrect readings will result. The wire must be joined using correct K-type connector.

The sensor comes with a threaded bung to make fitting easier, it should be fitted into the exhaust manifold or turbo housing no more than 50cm from the exhaust port. With turbocharged engines you must fit your sensor before the turbine. The sensor tip should extend to the middle of the exhaust to get the best accuracy. It is vital to select the right type of sensor for your engine.

EGT Sensor types
There are two types of sensor suitable for the two types of installation. The Normally Aspirated (NA) type is a 2mm diameter sesnor that is fast and responsive to the sudden snap temperature changes seen on a NA engine, but it's thin and will not withstand the extreme heat and vibration of a turbocharged engine.


The Turbo type sensor has a 6mm body to cope with heat and vibration and a 2mm tip to provide fast response.

Serial Connector

If you need to field program the unit or are planning on using the Datalogging facility you will need to connect your laptop or PC to the 9pin serial plug.

Operation

Each time the module is powered-up it must first heat the sensor before it can display the correct Air Fuel Ratio, when it is doing this you will see an 'H' followed by an increasing value, this shows that the module is operating correctly. Once the sensor is upto its operating temperature the AFR is displayed, if the sensor is tested in fresh air the AFR will skip around 20.0 to 21.0. With the sensor Installed in the exhaust you will see a lower value, because the sooty residue will contain unburnt fuel.

Disk/Download Contents

On this disk or downloaded file you will find:

Software

MegaTune

MegaTune provides realtime display generated by the VEMS Wideband & EGT Gauge

Click on the megatune.exe file in the MegaTune2.25 directory will load up the MegaTune application.

Field Programming New Firmware

Your Wideband & EGT Gauge will have been suppiled with the latest firmware available at the time of purchase, VEMS systems are constantly in development, and while they're always fit for purpose you may want to use one of the newer features in the newer releases. The firmware is the industry term for the software that runs on your VEMS Wideband & EGT Gauge. Ensure that you've connected your laptop or PC to the unit with the 9pin serial plug, and then double click the UploadFirmware.bat file. If you have any problems with the upload please refer to the Fault finding section at the end of this document.

Extended Functionality

To use the extended functions of the VEMS Wideband & EGT gauge, all you need to do is a little extra wiring and set a few parameters in MegaTune.

Lambda Out

VEMS Wideband & EGT gauge can simulate the behaviour of a standard Oxygen sensor, and is configurable as either Narrow or Wide band sensor's output. This is not intended to be a 'drop-in' replacement for an OEM sensor, but can be used by some 3rd party ECU and Datalogging systems. Ask your dealer for specific information.
Narrow Band Output
For many OEM systems it will be possible to use the gauge's LSM11 simulated output.
Wideband Output
The gauge can be configured to output the lambda reading across a range of voltages to allow most aftermarket ECUs to use Wideband feedback. We recommend three possible outputs: 1V/Lambda, 2V/Lambda, or 3V/Lambda.
So if you select 1V/Lambda the voltage from the Multifunction Plug's Pin-1 will be: 0.8V at lambda0.8, 1.0V at Lambda1, if you select 3V/Lambda then Lambda0.8 will give 2.4V and Lambda1 3.0v
Configuring Lambda Output
In MegaTune goto the Menu option Settings->Inputs and Outputs, and you will be presented with the following screen:

To set the output we use the Analog output settings box:

Connecting the RPM Signal

Using RPM allows you to provide a context to the information that you are datalogging.

Connecting An Analog Signal

Further context for your datalogs is obatained by feeding either the signal from your boost sensor for turbo/supercharged applications or throttle position sensor for normally aspirated.

Connecting To The Power Output

The Wideband & EGT unit has the ability to switch or pulse modulate a 5Amp load based on . To drive a solenoid, relay or other electro magnetic device you will need to use a diode for voltage protection.

Plugs and Connectors

Multifunction Plug

The additional functionality of the VEMS Wideband & EGT gauge is obtained through the 15pin multifunction plug, and configuring the gauge's firmware through MegaTune.

Serial Plug

The serial connector is a standard RS232 connector. It's primarily used by MegaTune to obtain the readings for its real time display, and is also used for field programming the gauge. The cable is a straight through connection

Fault Finding

Generally we have had very few reported problems and the ease of connection and operation of the system means that there is very little fault finding information that we can provide. The VESM team pride ourselves on the level of support we offer, so in the case of problems please contact your reseller. Display does not show Check the 1Amp fuse, if that's intact make sure that the power feed to the gauge is okay. If you have lost the display after uploading newer firmware it may have become corrupted, so it is advisable to upload the firmware again.

Display flashes -E- This indicates that the gauge has reset, the most common cause is a poor grounding connection, or insufficient power. Try testing by connecting your gauge power cables directly to a good battery. Serial port errors You will not be able to upload new firmware, or use MegaTune If you have any programs running that access the serial port. Make sure that you disable any programs like Palm Pilot Synchronizer for the time that you want to use the serial port for VEMS operations

Errors Uploading Firmware The most common problem is that the serial port (COM) is not correctly set. To rectify this, open UploadFirmware.bat in Windows Notepad, or right-click UploadFirmware.bat and select Edit from the drop-down menu. The COM port is specifed by the parameter -p COM1 change the number to the com port that you have the gague connected to.

MegaTune shows a MegaTune Open Error window If the first line in the window reads: The selected communication port (COMx) could not be opened. You need to first check the connection of the serial plug, if this is connected correctly then the problem may be due to MegaTune not being correctly configured. To set MegaTune to the correct serial port:


Select the correct port from the list, and click the 'Click to test' button to test the connection.